Vertically stacked coupled window assemblies for the purposes of Warranty, are more than one separate glazed panel and frame unit coupled together vertically in an external wall elevation.(Regardless of whether the assembly is contained within a single storey or extending to more stories)
The guidance within this article is limited to where coupled window assemblies are:
The guidance within this article should be read in conjunction with the guidance in the ‘External Windows and Doors’ section of our Technical Manual.
Vertically stacked coupled window assemblies must be part of a fully specified system and this must include details of dual sealed coupling joints, seals, fixings and other ancillary components.
Vertically stacked coupled window assemblies must be manufactured to BS 7412, BS 4873 or BS 6510. Timber coupled window and door assemblies are not acceptable for Warranty purposes.
Where vertically stacked coupled window assemblies are proposed, thermal breaks should be incorporated into the dual sealed coupling joints.
Vertically stacked coupled window assemblies need to be sealed at the edges and drained at the front to prevent water ingress at the edges.
Where any coupled window assemblies are proposed, they will require both off-site and on-site testing as detailed below.
Coupled window assemblies require off-site testing to BS EN 14351-1 and this must be for the complete coupled window assembly (with the dual sealed coupling joint in place), not just individual units.
Vertically stacked coupled window assemblies with higher levels of performance will be required for locations exposed to high levels of driving rain and this should be detailed by the system manufacturer.
Please note: individual units with third party certification usually do not cover a coupled window assembly scenario.
Where vertically stacked coupled window assemblies are proposed, on-site testing of water penetrations to critical joints (such as dual sealed coupling joints) in accordance with CWCT test methods is required to check to site workmanship of the building envelope as constructed. Areas and method of testing is to be agreed with the Warranty Surveyor prior to construction commencing. See CWCT Technical Note 41 and 102 for guidance.
Minimum requirements for on-site testing may be increased for areas subject to extreme weather conditions, exposed locations or coastal locations. The testing may also be increased where bespoke jointing systems are proposed as part of the construction.
Where vertically stacked coupled window assemblies are specified, pre-fabricated dual sealed coupling joints should be used for creating a weather tight joint. A dual sealed coupling joints must include:
Inner seals within the coupling joint must be placed within the joint during the assembly operation and be suitable for the proposed detailing. Suitable inner seals include impregnated foam tapes or flexible polymer gaskets. Wet sealants must not be solely relied upon.
If sealants (internal or external) are inaccessible or not easy to replace, their service life should match the service life of the window system as a minimum.
All seals must be permanently flexible and resistant to weathering.
All external sealants must be easy to replace.
Vertically stacked coupled window assemblies must incorporate a sill which projects from the wall by at least 25mm. The water drip must project the wall by at least 10mm.
Large glazed areas including vertically stacked coupled window assemblies will result in a rapid run off of rainfall across the surface area of the glazing in comparison to rainfall falling onto a masonry surface. This should be taken into account with the window system design to ensure rainwater is effectively discharged away from the building and does not impact on the weatherproof envelope.
Vertically stacked coupled window assemblies must be designed to be able to appropriately transfer its self-weight and imposed loads to the supporting structure.
The frame of the window needs to be able to resist the wind load in deflection, alternatively, the coupling joint needs to provide support and contribute to the overall stiffness of the system in resisting deflection.
Where the vertically stacked coupled window assembly extends to more than one window in both directions, the coupling joint in one direction must span the full width or height of the assembly and will have to carry all the load at the junction(s) between the window frames. It will also have to support the ends of the joining components running in the transverse direction.
Movement gaps are required around all external windows and doors to accommodate differences in movement between the window and the surrounding wall construction as specified in our ‘External Windows and Doors – General requirements’ section of our Technical Manual.
However, where vertically stacked coupled window assemblies are specified, the gap sizes between the frame and wall construction may need to be greater and this should be specified by the system manufacturer.
Where a vertically stacked coupled window assembly extends across a horizontal movement joint (in a timber framed building with lightweight cladding for example), the design should allow for suitable jointing of the window assembly that will accommodate predicted structural movement whilst remaining weather tight and transferring loads to the building structure.
While the guidance within this article is predominantly for low rise developments, it should be noted for developments of 5 storeys or over, developers and designers should consult with our Major Projects team for further advice. For testing the following will be required: